Pentek DGD-2501-20 Spun Polypropylene Filter Cartridge, 20″ x 4-1/2″


Pentek DGD-2501-20 - It has two separate gradient layers for higher particle reduction efficiency and dirt-loading capacity than standard spun or string-wound cartridges. The filter is made of spun polypropylene fibers for resistance to chemicals and bacteria. It has an initial pressure drop of less than 1 pound per square inch psi at a flow rate of 20 gallons per minute gpm, and operates over a temperature range of 40 to 145 degrees F 4.

4 to 62. 8 degrees C. This pentek dgd-2501-20 spun polypropylene filter cartridge reduces sand, silt, scale, commercial, and rust particles in residential, and municipal drinking water. The nominal filtration rating of the pre-filter layer is 25 microns, and the rating of the post-filter layer is 1 micron.

Pentek DGD-2501-20 Spun Polypropylene Filter Cartridge, 20" x 4-1/2" - This spun polypropylene filter cartridge meets national Sanitation Foundation/American National Standards Institute NSF/ANSI standard 42 for quality assurance, and is used for treatment of residential, commercial, and municipal drinking water. Specificationsnominal filtration rating pre-filter25 micronsNominal filtration rating post-filter1 micronInitial pressure drop at 20 gpm.

More information about Pentek DGD-2501-20

Pentek RFC20-BB Carbon Filter Cartridge, 20" x 4-1/2"


Pentair Industries RFC20-BB - Initial pressure drop of 090 psi at a flow rate of 4 gpm. Granular activated carbon GAC media with spun polypropylene core and polypropylene end caps for strength. For most residential, and industrial applications, commercial, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings.

This carbon filter cartridge is used for treatment of residential and commercial drinking water. SpecificationsInitial pressure drop at 4 gpm090 psichlorine reduction capacity70, 000 gallons at 4 gpmOperating temperature range40 to 125 degrees F 4. 4 to 51. 7 degrees cmaximum dimensions h x w20 x 4-1/2 inches 508 x 114 mmchlorine reduction capacity is the minimum total amount of water for which the free available chlorine FAC at a concentration of 2 ppm is reduced by at least 75%.

H is height, the horizontal distance from left to right; D is depth, the vertical distance from lowest to highest point; W is width, the horizontal distance from front to back. Water filters remove undesirable particles, adsorption, and microorganisms from water by means of a semipermeable barrier, chemicals, or biological processes.

Pentek RFC20-BB Carbon Filter Cartridge, 20" x 4-1/2" - Reduces chlorine taste and odor in drinking water. It is made of granular activated carbon gAC media with a spun polypropylene core and polypropylene end caps for strength, and there is a nitrile butadiene rubber Buna-N gasket to ensure a watertight seal. The filter has a porous polyethylene 70-micron outer shell to reduce carbon fines and other suspended particles in the filtered water.

More information about Pentair Industries RFC20-BB


Similar products



Housing Bracket for Big blue 10" and 20" filter housings


Watts BRK1-45100-PCL - White powder coated steel twin mounting bracket for 5000 Series, 10000 Series, and YTB 10" & YTB 20" Filter Housings. Porous polyethylene 70-micron outer shell reduces carbon fines and other particles. Temperature range of 40 to 125 degrees F 4. 4 to 51. 7 degrees C. Reduces chlorine taste and odor in drinking water.

Important note: units DO NOT include the nuts and washers. Initial pressure drop of 090 psi at a flow rate of 4 gpm. Filter housing mounting bracket for Big Blue 10" and 20" Filter Housings. Granular activated carbon GAC media with spun polypropylene core and polypropylene end caps for strength.

More information about Watts BRK1-45100-PCL


Similar products



Pentek 151122 OR-100 Buna-N O-ring for Big Blue Housings


Pentair Industries TIER1-OR-100 - Filter housing mounting bracket for Big Blue 10" and 20" Filter Housings. It has a diameter of 5-3/4 inches and is made of nitrile butadiene rubber Buna-N for flexibility and resistance to abrasion and tearing. Type: O-Ring. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization.

The performance of filters is measured by the minimum particle size that is blocked, the maximum flow rate, the downstream concentration of unwanted chemicals, the percentage of particles or microorganisms that are removed, and the amount of water that can be filtered before the filter must be replaced.

Pentek 151122 OR-100 Buna-N O-ring for Big Blue Housings - Reduces chlorine taste and odor in drinking water. Initial pressure drop of 090 psi at a flow rate of 4 gpm. For use with: pentek, pentair Water - Big Blue Housings Only. Granular activated carbon GAC media with spun polypropylene core and polypropylene end caps for strength. Water filters are used in a wide range of applications, including drinking water purification, and irrigation, swimming pools, industrial processes, among others.

Pentair manufactures industrial, commercial, and residential water filtration components and systems. For most residential, and industrial applications, commercial, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings.

More information about Pentair Industries TIER1-OR-100


Similar products



Pentek, Pentair Water 151122 Replacement for OEM Size Big Blue O-Ring Buna-N ORing 3 Pack - Captain O-Ring


Captain O-Ring LLC - For use with: pentek, pentair Water - Big Blue Housings Only. 151122 oem size o-rings are approximately 5. 5" inside Diameter x 5. 83" outside Diameter x 0165" thickness. Type: O-Ring. Compatible with the following filter housing models: pentek #10 and #20 big Blue opaque filter housings with 1" or 1-1/2" inlet/outlet connections APEC HBB-20/HBB-10 series input sizes: 3/4", 1", 1.

5", 1", hbc-20/hbc-10 series input sizes: 3/4", 1.5" ace hardware 49561 ametek kleen-plus hd-10-r50, w15-pr, 152022 culligan hd-950, 150469, 151122-27, 152017, bbs american plumber w10-pr, hd-950a pentek 150237, 152014, w10-or ametek kleen-plus 151122-03 culligan or-100, bbfs-222 the 151122 o-ring is a direct replacement for the following other part numbers: ace hardware 4001756 apec o-ring-hb american Plumber 152032, 150239, 152015, WWHC, W2010-PR, 01019189 Pentek 151122, BBFS-22, 152016, W2015-PR, BB BUNA-N What to expect: This item includes three 3 O-Rings in a resealable zip-top poly bag with "Captain O-Ring" branded packaging.

Pentek, Pentair Water 151122 Replacement for OEM Size Big Blue O-Ring Buna-N ORing 3 Pack - Captain O-Ring - Captain o-ring" is a registered trademark of Captain O-Ring LLC. Important note: units DO NOT include the nuts and washers. Porous polyethylene 70-micron outer shell reduces carbon fines and other particles. Material: Buna-N. Package Quantity: 1 Piece.

More information about Captain O-Ring LLC


Similar products



Pentek 155356-43 20" 75/25 Micron Dual Gradiant Poly Cart.


Pentek 155356-43 - Pentek dgd-7525-20 water filter replacement information: The Pentek DGD-7525-20 filters are easy to install in whole house systems or commercial water filter systems. Replace the pentek dgd-7525-20 sediment water filter cartridge every 2 months or 8, 000 gallons of water. The pentek dgd-7525-20 sediment water filter cartridge also fits cuno aquapure, teledyne Water Pik, Honeywell, Sears, General Electric, Flotec, Master Plumber, Ace, Omni, Fulflo, American Plumber and most other water filter housings for 20" x 4.

5" filters. Direct replacement for the following part numbers see description below for full water filter compatibility list: ace hardware 4001756; American Plumber 152032, W10-OR; APEC O-RING-HB; Ametek Kleen-Plus 151122-03; Culligan OR-100, 151122-27, 01019189; Pentek 151122, BB BUNA-N. Manufactured and warrantied by Captain O-Ring LLC, with decades of experience in the sealing and chemical industry.

Pentek 155356-43 20" 75/25 Micron Dual Gradiant Poly Cart. - Two separate gradient density layers that enhance cartridge performance. Filter depth is increased to a full 233% of standard spun-polypropylene or string-wound filters. Porous polyethylene 70-micron outer shell reduces carbon fines and other particles. Pentek dgd-7525-20 water filter specs: type: dual gradient density dimensions:20" x 4 1/2" 254 mm x 114 mm Pre-Filter Micron Rating Nominal:75 Post-Filter Micron Rating Nominal:25 Temperature:40F to 145F 4.

More information about Pentek 155356-43


Similar products



Pentek EPM-20BB Carbon Block Filter Cartridge, 20" x 4-5/8", 10 Microns


Pentair Industries EPM-20BB - Important note: units DO NOT include the nuts and washers. Direct replacement for the following part numbers see description below for full water filter compatibility list: ace hardware 4001756; American Plumber 152032, 151122-27, 01019189; Pentek 151122, W10-OR; APEC O-RING-HB; Ametek Kleen-Plus 151122-03; Culligan OR-100, BB BUNA-N.

Manufactured and warrantied by Captain O-Ring LLC, with decades of experience in the sealing and chemical industry. Two separate gradient density layers that enhance cartridge performance. Porous polyethylene 70-micron outer shell reduces carbon fines and other particles. Temperature range of 40 to 180 degrees F 4.

Pentek EPM-20BB Carbon Block Filter Cartridge, 20" x 4-5/8", 10 Microns - 4 to 82. 2 degrees C. This pentek epm-20bb carbon block filter cartridge reduces fine sediment and chlorine taste and odor in residential and commercial drinking water. Reduces fine sediment and chlorine taste and odor in residential and commercial drinking water. Initial pressure drop of 090 psi at a flow rate of 4 gpm.

Granular activated carbon GAC media with spun polypropylene core and polypropylene end caps for strength. Type: O-Ring.

More information about Pentair Industries EPM-20BB


Similar products



Pentek CBC-20BB Carbon Block Filter Cartridge, 20" x 4-5/8", 0.5 Micron


Pentair Industries CBC20-BB - Nominal filtration rating of 10 microns. This carbon block filter cartridge meets national Sanitation Foundation/American National Standards Institute NSF/ANSI standard 42 for quality assurance, and is for purification of residential and commercial drinking water. SpecificationsNominal filtration rating0

5 micronsinitial pressure drop at 4 gpm8. 5 psiremoval of protozoan cysts99. 95%chlorine reduction capacity150, 000 gallons at 4 gpmTemperature range40 to 180 degrees F 4. 4 to 82. 2 degrees cmaximum dimensions h x w9-3/4 x 4-5/8 inches 248 x 118 mmMaterials certificationNSF/ANSI standard 42The nominal filtration rating is for a particle removal efficiency of 85%.

Pentek CBC-20BB Carbon Block Filter Cartridge, 20" x 4-5/8", 0.5 Micron - Initial pressure drop of 8. 5 psi at a flow rate of 4 gpm. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. It has a nominal 85% filtration rating of 05 micron, and 99. 95% efficiency for the reduction of protozoan cysts.

. It will reduce free available chlorine fac at 2 parts per million ppm by at least 90% in up to 150, 000 gallons at a flow rate of 4 gallons per minute gpm.

More information about Pentair Industries CBC20-BB


Similar products



Pentek 150467 20-BB 3/4" Big Blue Filter Housing with Pressure Relief


Pentair Industries 3/4" #20 BB Black/Blue HFPP w/PR - Porous polyethylene 70-micron outer shell reduces carbon fines and other particles. The performance of filters is measured by the minimum particle size that is blocked, the downstream concentration of unwanted chemicals, the percentage of particles or microorganisms that are removed, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced.

This filter housing meets national sanitation foundation/american National Standards Institute NSF/ANSI standard 42 for quality assurance, and irrigation, including residential drinking water filtration, food service, and is for use in various high-flow applications, among others. Specifications filter cartridge size h x w sold separately 20 x 4-1/2 inches 508 x 114 mm Initial pressure drop at 15 gpm 2 psi Maximum temperature 100 degrees F 37.

Pentek 150467 20-BB 3/4" Big Blue Filter Housing with Pressure Relief - 8 degrees c maximum pressure 90 psi maximum dimensions h x w 23-3/8 x 7-1/4 inches 594 x 184 mm materials and structural integrity certification NSF/ANSI standard 42H is height, the horizontal distance from left to right; D is depth, the vertical distance from lowest to highest point; W is width, the horizontal distance from front to back.

Water filters remove undesirable particles, and microorganisms from water by means of a semipermeable barrier, chemicals, adsorption, or biological processes. The housing can be used with a 20” x 4-1/2" filter cartridge sold separately. Bonded pac media with polyolefin wraps and polyethylene netting. Filter depth is increased to a full 233% of standard spun-polypropylene or string-wound filters.

151122 oem size o-rings are approximately 5.

More information about Pentair Industries 3/4" #20 BB Black/Blue HFPP w/PR


Similar products



Pentek NCP-20BB Pleated Carbon-Impregnated Polyester Filter Cartridge, 20" x 4-1/2", 10 Microns


Pentair Industries NCP-20BB - Initial pressure drop of 1 psi at a flow rate of 10 gpm. This filter cartridge is for use in rural, residential, and municipal drinking water purification. Specificationsnominal filtration rating10 micronsInitial pressure drop at 10 gpm1 psiChlorine reduction capacity1, 000 gallons at 4 gpmTemperature range40 to 125 degrees F 4.

4 to 51. 7 degrees cmaximum dimensions h x w20 x 2-1/2 inches 508 x 114 mmThe nominal filtration rating is for a particle removal efficiency of 85%. Nominal filtration rating of 05 micron. They are made of densely packed synthetic or natural fibers that trap suspended particles, or substances that cause a chemical change, materials that block microbes or adsorb unwanted chemicals, such as acid neutralization.

Pentek NCP-20BB Pleated Carbon-Impregnated Polyester Filter Cartridge, 20" x 4-1/2", 10 Microns - Filter housing mounting bracket for Big Blue 10" and 20" Filter Housings. Reduces fine sediment and chlorine taste and odor in residential and commercial drinking water. Reduces chlorine taste and odor in drinking water. It has a nominal filtration rating of 10 microns at an efficiency of 85%. Initial pressure drop of 2 psi at a flow rate of 15 gpm.

Material: Buna-N. Temperature range of 40 to 125 degrees F 4.

More information about Pentair Industries NCP-20BB


Similar products



Tier1 DGD-5005-20 5 Micron 20 x 4.5 Spun Wound Polypropylene Sediment Hydronix SDC-45-2005 Comparable Replacement Water Filter 2 Pack


Tier1 - Pressure relief button for easier cartridge replacement. Material: Buna-N. Initial pressure drop of 4 psi at a flow rate of 4 gpm. Temperature range of 40 to 125 degrees F 4. 4 to 51. 7 degrees C. Reduces fine sediment, chlorine taste and odor, and protozoan cysts in residential and commercial drinking water. In addition, these filters help to ensure your water tastes great while reducing the risk of sediment corrosion in your fixtures and appliances.

Temperature range of 40 to 125 degrees F 4. 4 to 51. 7 degrees C. Replace your old pentek dgd-5005-20 or liquatec sDF-45-2005 with a Tier1 SDF-45-2005. Direct replacement for the following part numbers see description below for full water filter compatibility list: ace hardware 4001756; American Plumber 152032, W10-OR; APEC O-RING-HB; Ametek Kleen-Plus 151122-03; Culligan OR-100, 151122-27, 01019189; Pentek 151122, BB BUNA-N.

Tier1 DGD-5005-20 5 Micron 20 x 4.5 Spun Wound Polypropylene Sediment Hydronix SDC-45-2005 Comparable Replacement Water Filter 2 Pack - Manufactured and warrantied by Captain O-Ring LLC, with decades of experience in the sealing and chemical industry. Two separate gradient density layers that enhance cartridge performance. Package Quantity: 1 Piece. Temperature range of 40 to 180 degrees F 4. 4 to 82.

More information about Tier1


Similar products